SSR-F-AA系列帶保險絲型單相固態繼電器現有型號:SSR-F-10AA/SSR-F-10AA-H/SSR-F-25AA/SSR-F-25AA-H/SSR-F-40AA/SSR-F-40AA-H

SSR-F-AA系列帶保險絲型單相固態繼電器產品特點:

＊ High Dielectric strength over 4KV

＊ High Isolation strength over 100MΩ/500VDC

＊ With over heat protection Circuit（120℃）

＊ High surge current sustenance

＊ High surge voltage sustenance

＊ Conformity with EN60947-4-3 and EN60950

＊ 高電介強度超過4KV

＊ 高絕緣強度超過100MΩ/500VDC

＊ 附過熱保護回路可防止過熱破壞

＊ 耐瞬間電流超過額定電流10倍以上

＊ 附雙重突波吸收回路有效防止突波破壞

＊ 符合EN60947-4-3 and EN60950標準

Control method / 控制方式

Zero cross trigger method

Output will be turned ON or Turned OFF

only on the Zero point of sine wave, that may avoid

to occur the EMI or RFI. Specially suited to control

the resistive, capacitive and non-saturated inductive

load.

輸出只有在正弦波的零點上有輸入訊號時才會打開或

關閉，以避免產生突波或EMI / RFI。特別適用於控制

阻抗性或電容性或不飽和感抗性等負載。

Variable resistance control

method（Trimmer control）

Power output is controlled by the Trigger angle of

the Triac that is controlled with variable resistor.

（250KΩ/110VAC, 500KΩ/220VAC, 1MΩ/220VAC）

以可變電阻控制Triac的觸發角來控制輸出功率。

（250KΩ/110VAC, 500KΩ/220VAC, 1MΩ/380VAC）

■ Specification【Rated current corresponding to Resistive load】

■ Notice of use / 使用注意事項

1＞ To protect the solid state module against a short-circuit of the load, please use a fuse with a I2t value ＜ 1/2 I2t

value specified.

請加裝快速保險絲（I2t value 小於額定值的一半），以防止因負載短路而造成固態模組燒毀。

2＞ The thermal conductive silicone rubber or thermal grease is required

When the solid state module is mounted on a heat sink

本固態模組加裝散熱器時務必墊高導熱系數的矽膠片或散熱膏【導熱系數（K）＞4.5】。

3＞ The rated current is corresponding to a resistive load, if the solid state module is applied in other loads,

Please consider the inrush current at turn on and the surge voltage at turn off.

本固態模組所標示的額定電流是以電阻性負載為準，如果使用在其他負載上須考慮起動電流及關機突波。

＊ Electric discharge lamps: Those loads have the「inrush current」at turn on and the「surge voltage」at turn off,

please use「high voltage type」on 220VAC mains.

電子起動式燈具（如日光燈）：須考慮起動電流及關機突波，220VAC電源系統請選用「高壓型」。

＊ Incandescent lamp: The rated current of the module must be over 4 times of the incandescent lamp current.

炙熱燈泡（如IR燈管）： 須考慮起動電流，固態模組的額定電流須大於炙熱燈泡電流的「四倍」。

＊ Three phase motors: The rated current of the s module must be over 4 times of the three phase motor average

current .

三相馬達：須考慮起動電流，固態模組的額定電流須大於三相馬達平均電流的「四倍」。

＊ Transformer loads: The rated current of the module must be over 10 times of the transformer current.

變壓器負載：須考慮反電動電流，固態模組的額定電流須大於變壓負載電流的「十倍」。

＊ Capacitor loads, the rated current of the module must be over 3 times of the capacitor current .

電容性負載：須考慮充電瞬間電流，固態模組的額定電流須大於電容性負載電流的「三倍」。